Hook up stock radio to amp, yahoo answers

Yahoo Answers

Hook up stock radio to amp

However, if you're asking about the wires from the vehicle, it will depend on the manufacturer. Hide all of the cables and wires behind carpeting, panels or trim for a cleaner and more professional look. Check the manuals included with your line-out converter, gainesville dating service stereo and amplifier for complete installation instructions for your system. Start with a pilot hole and then work your way up to a size that will fit your wire. Have your power wire taunt and find out where your cap.

Check your balance first on your radio's settings. Connect the red power wire and ground wire you prepped earlier to the proper inputs on your amp. Make sure that you use cables with the correct resistance or impedance for your setup. Just cut the power wire, best dating site 50 insert the inline fuse and reattach.

  • Run the wire under the carpet by removing the rocker panel and kick panel covers.
  • The installation is quick and easy and won't require removing your factory head unit.
  • Start from the interior of the car, and make sure the wire won't get pinched or caught on anything.
  • If you don't already have one, purchase a car amplifier with speaker-level inputs and also purchase an amp installation kit.

It Still Works

Connect your amplifier or powered sub to your car's stock head unit. Stock car stereo systems usually do not pack much punch. If you have a stock stereo and you have the remote wire there you want to in twine the remote wire with the power wire before inserting in the power slot for amp. Make sure you know how to reactivate your radio before doing this, if your radio has a security system. Will the wires still match up on the aftermarket radio I purchased?

Hook up sub to stock radio

Can I hook up a amp and sub to a stock bose radio

If the amp doesn't seem to be working properly, disconnect your battery again and go back and double-check all of your wiring for possible damaged wire, grounded wire or loose connections. If all connections seem correct but the speaker is not functioning properly, consult an expert at your local electronics store. Connect your amplifier to your speaker by running the positive and negative speaker wires to the proper terminals on your speaker. Tune them gain until the subs sound good. Tips If your amp doesn't turn on, not check the amp fuses.

How to Add an Amplifier to a Factory Stereo

How to hook up subs and amp to stock stereo in car

Set all of the input level gain controls to their lowest setting. Don't forget to test your rem wire before you assume it works. If you don't hear distortion even at the loudest setting, your the head unit is in good shape. Always be careful with electricity.

How to hook up subs and amp to stock stereo in car

If it does, then turn your car off and make sure the amp turns off as well so it doesn't drain your battery. Warnings Always Disconnect the Negative terminal from your battery before doing anything with electricity on your car. Make sure your speaker's impedance in ohms matches the output impedance of your amplifier.

How to Wire an Amp to a Sub and Head Unit 12 Steps

Make sure you always turn off your amp when you leave your car, it will overheat and drain your battery. Now attach a line of speaker wire to each splice and secure with electrical tape. To submit your questions or ideas, or to simply learn more about It Still Works, contact us. Use a capacitor to prevent voltage drops caused by deep bass hits, i. If there is no available hole, use a power drill and steel bits to drill one.

Connect the speaker wires from the amplifier to the speakers. Things You'll Need Amplifier. This will prevent noise in the system. Make sure to put the right rear positive wire into the right rear positive speaker-level input, and do the same for right rear negative wire until all four of the wires are connected. Did I need to put fuse between the first and second battery?

Installing an amp can be done without the help of a professional, allowing you to get great sound without an installation fee. Run the red power wire from your amp installation kit from the positive terminal on your battery through your car's cabin to the location of the amp. Items you will need Amplifier with speaker-level inputs Amp installation kit gauge speaker wire Electrical tape Wire stripper Socket set or adjustable wrench Screwdriver. The sub cuts on and off at high volume when I use the auxiliary cord to phone. Your amp could be installed near the speaker in the trunk or under a seat.

In other words, do not mount it on a metal surface. Warnings Never drill inside a car's parts unless you know exactly where the drill bit is going. Clipping is the number one reason of bass distortion. Run the power wire to the battery.

Report Abuse

Subwoofers can be large speakers that are usually housed in speaker enclosures installed in the trunk of the car. Insert the main power wire fuse once all the connections for the other wires are in place. The remote antenna power wire is responsible for the antenna coming out of a car with a retractable antenna.

How to Install a Car Amp (with Pictures) - wikiHow

Video of the Day

You can usually find one on the sidewall behind the carpeting. Mount your amplifier on a solid surface that will not conduct electricity. If you're using an after market head unit, go to an electronics store's stereo department and ask for a wiring harness from your car to the after market head unit.

Hook up amplifier to stock radio

Run this wire back to your amp and hook it into the speaker-level inputs. Hook it to a fuse connected to ignition turn on, like your accessory power fuse. If they are, then hook up an external speaker to the radio's output for that side to see if it is the radio at fault.

  1. Brought to you by Techwalla.
  2. While your key and radio is on, disconnect and connect the remote wire to the amp.
  3. Make sure the control wire from your deck to the amp is connected.
  4. Subs and amps should be matched as closely as possible for best performance and longevity.
  5. You want an amp more powerful than your sub, because you don't want your sub to clip.
Can I hook up a amp and sub to a stock bose radio

Carefully splice into the positive and negative wire on both the right and left rear speakers using a wire stripper. Now that your amp is tapped into your car's factory audio system, run speaker wires from the amp's speaker outputs to the speaker s or sub-woofer s you want the amp to power. Run the power wire to your amp. Consult the schematic for your deck to be sure which wire this is.

How to Wire an Amp & Subwoofers Into a Stock Stereo

Generally, the positive wire will be red and the negative will be black. Do not attempt to install an amp if you do not feel comfortable with the procedure. Now for the Remote blue wire. Another important factor to consider is Ohms. Get your capacitor as close to the amp as possible, and use the same ground as you did for the amp.

Last thing you need is a dead battery. Cookies make wikiHow better. The wires are not grounded properly, check to make sure the surface is clean, unpainted metal. This converter can then be connected directly to your amplifier's line level inputs. The only time you should see a voltage reading is if you're measuring from a battery positive source and ground.

  • Hiv dating sites in tanzania
  • Dating websites kansas
  • Free southampton dating sites
  • Dating for upper class
  • Should i use zoosk dating site
  • Online dating relationships dangers
  • Childless by choice dating sites